Permanent Outdoor Lighting Aluminum Track for Rooflines and Facades
Permanent outdoor lighting is a fixed architectural line, not a seasonal decoration. The hardware is an extruded 6063-T5 aluminum track fastened to the structure, an LED strip carried inside it, and a diffuser that turns individual diodes into one continuous bar of light. We extrude, finish and cut the track in-house, and supply the gaskets, end caps and clips that make the assembly weatherproof.
Two details decide how it looks in year three. The UV-stabilized opal polycarbonate diffuser removes diode points, so the run reads as a drawn line instead of a scalloped strip. The extrusion also works as a heat sink: heat leaves the strip into the metal rather than being trapped against a wooden fascia, which keeps output and service life stable.
Outdoor is a specification, not a location. A sealed assembly — gaskets, closed end caps, silicone-coated or potted strip — reaches IP65 or IP67; the same parts assembled carelessly fail by moisture tracking. 24 V is the default for rooflines, because it tolerates roughly twice the run length of 12 V before voltage drop becomes visible.
Sections cover surface-mounted fascia and soffit runs, V-shaped and 90-degree corner profiles for gable ends and porch returns, recessed details for step nosings and wall caps, and wide or deep sections for higher output. Anodized or powder-coated to RAL, cut to increments, drilled and kitted per project.
- Technical Specifications
- Applications
- Advantages
- FAQ
- Recommended Products
Technical Specifications
| Item | Specification |
| Product name | Permanent Outdoor Lighting Aluminum Track |
| Alloy and temper | 6063-T5 (6061-T6 available for structural sections) |
| Extrusion | Hot extruded; straightness and twist per GB/T 5237 tolerance class |
| Section families | Surface-mounted fascia / soffit, V-shaped, 90-degree corner, recessed, wide and deep |
| Profile length | 1 m / 2 m / 2.5 m / 3 m, or cut to fixed project increments |
| Wall thickness | 1.2 mm – 2.0 mm |
| Strip width accepted | 8 mm – 12 mm |
| Diffuser | Opal polycarbonate, UV-stabilized; snap-in or compression fit |
| Ingress protection | IP65 as sealed assembly; IP67 with potted strip |
| Operating voltage | 24 VDC standard, 12 VDC available |
| Surface finish | Anodized (silver / black / champagne) or powder coated to RAL, coating ≥ 60 μm |
| Light source | RGB, RGBW or single colour strip, buyer-specified |
| Fixing | Stainless steel clips, screws, mounting channel |
| Accessories | End caps, gaskets, corner connectors, connecting pins, drain details |
| Operating temperature | −25 °C to +50 °C |
| Place of Origin | Shanghai, China |
| Brand Name | Qinkai / OEM |
| Model Number | QK-POL series (assigned per section) |
| Certification | Mill test certificate per lot; salt-spray and coating adhesion reports on request |
| MOQ | To be confirmed per section |


Applications
· Rooflines. Fascia, soffit and gable runs, switched between everyday warm white and colour scenes.
· Entry and steps. Recessed sections along step nosings and wall caps, so light appears without a visible fixture.
· Landscape and facade. Retaining wall copings, path edges, canopy and parapet outlines.
· Retrofit. Replacing seasonal clip-on strings on an existing house without re-cladding the elevation.
Application image width on page: 720 px when a single image is used.
Advantages
· Extruded in-house. Alloy, temper and wall thickness are controlled at the press instead of being bought back from a trading company.
· Cross-section sized as a heat sink. Thermal path from the strip to the metal body keeps output and service life stable past the second winter.
· No visible diode points. UV-stabilized opal polycarbonate diffuses across the full profile width; uniform bar at driveway distance.
· Sealed as a system, not sold as a profile. Gaskets, end caps and drain details ship with the extrusion, which is what makes IP65 or IP67 achievable as assembled.
· Geometry that closes. V-shaped and corner sections handle the 90-degree change at gable ends and porch returns; mitring and forming service available.
· Colour that holds. Anodized or ≥ 60 μm powder coating in standard or custom RAL, tested per order.
· Project-ready processing. Cut to fixed increments, drilled to a mounting pattern, kitted and packed per installation sequence.
· One run, year-round use. With RGBW strip, a single installed line carries everyday white plus holiday scenes, replacing temporary strings bought and discarded each season.
FAQ
Is this a complete light fixture?
It is the aluminum track system: extrusion, diffuser, end caps, gaskets and fixing accessories. The LED strip, driver and controller are either supplied by the buyer or specified with us as a matched assembly.
What IP rating can the finished run reach?
IP65 as a sealed assembly and IP67 with a potted strip. The rating depends on the end caps, gaskets and strip protection being assembled correctly — not on the profile alone.
Should I specify 12 V or 24 V?
24 V for rooflines. At equal brightness a 24 V system tolerates roughly twice the run length of 12 V before voltage drop becomes visible. Where one feed cannot cover the geometry, add a second feed.
Can the track be cut and drilled on site?
Yes, within the stated cut increments for the section. Cut ends must be closed with end caps and the cut kept away from gasket seats; drilling should follow the mounting pattern supplied with the order.
Will the diffuser yellow outdoors?
Yellowing is a material decision, not an inevitability. We specify UV-stabilized polycarbonate; unstabilized or polystyrene covers degrade within a few summers.
Can it be installed on an existing house?
Yes. Surface-mounted fascia and soffit sections fix with clips or screws into the substrate. Recessed sections require a rebate, so they suit new build or re-cladding.
RGB or RGBW?
RGBW for permanent installations. White remains the everyday setting for curb appeal and colour is an overlay; pure RGB cannot produce a usable warm white.
Do you support custom lengths, colours and drilling?
Yes — OEM and ODM. Send the section drawing or a sample, the mounting pattern and the finish reference; we confirm the drawing before production.
